Features:

  • US Design Patented
  • Made of dual coated 24oz marine grade vinyl, heavy duty aluminum powder coated frames, and comes with stainless steel clamps for easy installation and great durability.
  • Pre-assembled horizontal crossbars offer support and conveniently fold up with the cover providing full bed access.
  • Easy No-Drilling installation with the provided instruction and hardware. (Small holes will need to be cut for vehicle equipped with Over-the-Bedrail bed liner to secure the clamps; Works with Under-the-Bedrail bed liner without modification. )
  • TYGER Limited Lifetime ! (Please measure your truck bed size before ordering. We accept returns, however customer will assume the return shipping cost if ordered wrong. )
TYGER Tonneau Cover - A fantastic product!!

I've been a truck man for 35 years. My last pickup had a fiberglass tonneau cover with hydraulic arms. Everything stayed nice and dry and it locked, but it was heavy and awkward when it needed to come off; I think I only removed it twice in six years. When using my truck to move something large, even an appliance, the cover simply wouldn't allow for it; it would only open to 40 degrees or so. Before that, I had two different rollup covers. One had the struts built in, the other had supporting arms that had to be sprung in and out of the truck bed. I hated both of them; they were a major pain and water always pooled on them anyway. So I decided to give it another shot when I got a wonderful used 2007 F150 last Saturday, and try a tri-fold. It came today, installation was a breeze, and I couldn't be happier. The cover comes 99% assembled and is in a giant drawstring bag, good for storage. (Tyger has also included a handy little trouble light, a strip of adhesive foam rubber, and a small bag of nuts and bolts. Took me a few minutes to figure out that these bolts are spares for the four latches.) This cover requires no drilling, no measuring, no rails or guides, no degree in physics or engineering. You simply lay the folded cover behind the cab, get it centered, tighten the front clamps with the two knobs, fold it back, and tighten the two rear clamps. I stood there thinking, "Surely it can't be this easy," but it is. The entire cover has a rubber seal around the edge, so it snugs down nice and tight to the truck bed and tailgate. The front clamps stay in place unless you're removing the entire cover. A few notes... The rear clamps must be folded/closed up inside the cover before folding the cover itself. Second, the front wall on my F150 bed is just a touch shorter than the sides, so I used the strip of adhesive foam rubber here, just behind the cab; you sure don't want air getting in under the front edge. Lastly, I'm going to attach some adhesive velcro tabs to the plastic latches that keep the cover in place when it's folded. As it stands, it appears they'll be constantly flapping around in the wind (see photo). My only modification came on the front clamps. The top of the F150 bed isn't rolled, meaning it's just a thin metal lip that's bent over. The front clamps have a wide mouth so they can grip the underside edge of a wider truck bed. I wasn't thrilled with the bite I was getting, so I cut some fir to 1"x4"x5/8", and fit it inside the mouth of the clamp (see photo). This tightened the bite considerably, and I was able to get a more satisfactory seal around the front edge. This cover will definitely keep your cargo safe from the elements, and should reduce wind drag in the bed, thus increasing MPG. It's not a security device; it might keep someone from a crime of opportunity in the big box store parking lot, but if someone wants in your truck and they have a box cutter, this won't stop them. Otherwise, it's a top drawer product, highly recommended.

Great cover!

I'm rating this 5 Stars because of value. Are there better covers out there yes. I sell Fords for a living so I have seen ALOT of different makes for covers. There are some really cool covers that have drains in them and your bed will be bone dry all the time! Those covers run between $1,500-$2,000 I'm not spending that kind of money for my cover. $229 for a cover fit the bill. This cover seals GREAT! The gaskets on it are nice and big and even comes with additional foam to put on the bed if you don't have a bed liner. The cover clips right into the bed with no screws (major concern since I am leasing the truck) and I will be able to remove the cover and sell it for $200 in 2 years once my lease is over. Great buy. Can't be more excited for a trip down the SHORE and some E-A-G-L-E-S ... EAGLES tailgates!

Great value. Keeps the water out

Bought this as a gift for my husbands new truck. It is worth the price and the quality is better than expected. He gets car washes every week sometimes twice a week and has never had any leakage. There are other truck bed covers that are more expensive but this one works just as great and was not over budget.

Almost Perfect except for rear clamps not having deep enough channels to miss plastic edge.

I bought this for my Ford F150, and though the least expensive of all Tri-fold Tonneau covers, I can't imagine that anything else would have justified paying a higher price. Went on very easy with the clamps all pre-attached. Lay it out, line it up, slightly tighten the front clamps. Unfold it, verify alignment, fold back up to finalize tightening of front clamps, the unfold it and tighten the back clamps. That's it! Looks great. I'll update if it has any issues. One slight engineering mishap. My pickup has a plastic protective edge along the top. I don't know if it comes that way from Ford or is after market. But the lip of it drops about 3/16" inch below the lip of the metal. Just enough that the channel of the clamp isn't deep enough to miss it. In order to have the clamp grab the metal lip and not bulge the plastic lip, I had to do a little trimming. See picture. But a minor adjustment.

Great look and easy install.

This cover looks great on my 2016 Ford F-150 and is reasonably priced. It is easy to install and my main advice is just be certain you order the correct bed length and their pictures with he products make it an easy thing to check. Installed last night and my only minor concern is the back corner by the tail gate is a little off the bed allowing water in but I probably just need to tighten the clamp a little more. I didn't use the foam hey provide to have a better seal around the bed. That would also help. I also really appreciate the bag that comes with it. When I need to haul stuff I can take the cover off, put it in the bag and store it. Not sure yet if it will fit in the back of the cab but that's a minor concern.

Beyond satisfied!

Couldn't be more happy with this purchase. The price is great, and so is the quality. I waited a few months before reviewing this cover so I could give an honest opinion. Installation: took a solid 20 minutes by myself. I know some people said it took them 5 but I wish I would have taken more time. The only time consuming part is placement of the weather stripping. This part should not be rushed. Other than that, it already comes assembled so you just apply and go. Waterproofing: almost 100% waterproof. I drove from PA to VT in snow and rain and my bed didn't get wet at all. I drove across PA last weekend and it poured for a solid three hours and I passed big trucks that sprayed me and very little water got in. I took my truck through a car wash, the ones where the pressure wash everything but the inside of the cab, had very little water come in where the bed meets the cab. This was my mistake because I didn't take my time putting on the weather strip. I will fix this though because it did come with extra weather stripping. I washed my truck by hand and sprayed it with the garden hose to deliberately try and get water in and again, very little water got in! Bottom line: extremely happy with this purchase. Would definitely buy again and recommend to anyone. Much better than other expensive covers and can easily come off when you have to haul something big.

The cover fits beautifully and was easy to install and remove when needed

I purchased the Tyger Tri-Fold truck bed cover for 2016 Ford Supercrew with 5.5 ft. bed. The cover fits beautifully and was easy to install and remove when needed. Have had the cover for a year and a half and am very pleased. We had an exceptional amount of snow in Reno, NV. last year, dropping as much as a foot of snow on the cover overnight, before I could get out and broom the snow from the cover, and the cover held up very well. This last summer (2017), temperatures were above 100 degrees, and the cover still looks like new after cleaning. The material and workmanship is very good. One of the best investments that I've made. Highly recommended.

Best Top for Me and Cost Beats Most Others I've Seen. Easy Install, just a few minutes, do drilling, no tools needed.

Love this top, bought one for my son' F150 a couple years ago. Just bought one for my F150. Great top, easy to install. Easy to fold up, just undo two hand clamps. Easy to remove, just undo two hand clamps, fold the three sections, undo two more hand clamps. Keep the truck bed clean and dry. My son's truck sits outside year-round here in Michigan. Snow, ice, rain, sun. After a couple of years, now, the top looks just like new. Taking a picture right now and will post.

2016 F150 Platinum

First pickup, great cover, easy to install, use the provided weather strip at the front of the bed. There is a tiny gap at the back by the tailgate. Rain proof, haven't been through a car wash yet. Tailgate closes with cover down just fine. Highly recommended if you are a truck newbie and skeptical about what to buy.

It fit the F-150 like a glove

Here is the bottom line guys... For the price it is well worth the money!. It fit the F-150 like a glove....Just a little tight on coverage at the tailgate, but it will keep the leaves and snow out.....nosiey eyes out too. Remember it is a soft top... so valuables in the bed are only a knife cut away from being protected. but you didn't spend $400 either! It has 2 quick release handles at the back so you can fold it forward to open 2/3 of the bed. To take it off completely you need to release the front panel which is held by clips that have a T handle screw. (no tools required) When the cover is removed you can place it in the nice bag that it is shipped in. It will fit behind the drivers seat (at an angle) if you have a Super Crew and no passengers or store it in the bed. IT looks as good as it does in the pictures. Id buy it again,knowing what I know now. Quality construction is good.

Full Reviews