Features:

  • Basic Radar Detector Rear View Mounting Solutiuon for LESS
  • No More Troublesome Suction Cups and Install in Most Cars min Minutes ****PLEASE MAKE SURE THAT YOU HAVE AT LEAST 1 INCH OF STEM SPACE TO INSTALL THIS MOUNT*** (Not Compatible w/Corvette & vehicle with short stem)
  • Compatible Escort Models: PASSPORT 9500ix, 9500i, 9500i, 8500, X50 BLUE RED, 7500, 7500S, 6800, STI, C65 SOLO S2, SOLO S3, SOLO S4, SC 55, S75
  • Beltronics Radar: PRO 100,200,300 500 GX 65,STI DRIVER,STI MAGNUM,RX 65 BLUE RX 65 RED VECTOR 995,VECTOR 955 VECTOR 940 V6 V8 V10
  • PLEASE NOTE THAT YOU WILL NEED AT LEAST 1 INCH OF CLEAR STEM SPACE ON YOUR MIRROR TO INSTALL THIS MOUNT ***THIS HOLDER IS NOT COMPATIBLE WITH PASSPORT MAX/MAX2/REDLINE***
Highly Recommended Mirror Mount

Works as well or better than a more expensive model I have in another car. Very easy to install and adjust. If you are looking for a mirror mount for your radar detector, then I would highly recommend this mount. I currently have an Escort Passport 9500ix on this mount in my Mazda MX5. Zoom Zoom Zoom!

Good fit for Porsche 991

I was hesitant at 1st as customer service said it wouldn't fit mirror on my Porsche 991. Took a chance and it worked like a charm! I just needed to change the bolt cause they were too long, but a cheap fix from Home Depot. So far so good & sturdy.

Very stable for Escort/Beltronics Radar Detectors, but your mirror shouldn't be TOO tall!

This worked just fine on my 2012 Honda CR-V meaning that it clears just barely to not mess with the day/night lever below the mirror. If you have a tall mirror (or if you added a "wide angle" mirror adapter on top of your OEM mirror), this probably won't work well because you won't have sufficient clearance to insert the radar detector to the bracket... in other words, the detector will hit your wide angle mirror adapter/add-on). If you have just an OEM mirror, it will be just fine. The little "arm" that swivels between the mirror stem and the detector plate is about an inch, just barely enough for most cars. Installation is straight forward, just a little frustrating if you have big hands since it's a pretty tight space up there.... careful about dropping the screws. I found it easier to basically remove just one screw/bolt and leaving the other screw/bolt almost all the way out and sliding this to the mirror stem vs. removing both screws and trying to hold two pieces together while putting the screw/bolt (not easy if you do it by yourself unless you use a clamp). All in all, a good purchase... just wished the little arm was maybe 2" to leave extra clearance between the mirror and radar detector and to allow the radar to move back a bit vs. stick out 3" in front of the mirror.

It does the basic job perfectly. Mounted in Kia Sorento 2016 with 8500-X50

It does the job perfectly. The only thing to be improved is different arm construction so it could extend lower/higher/more forward or backward but this would require completely different arm.

Perfect and so easy to install!

Absolutely amazing product, it was so simple to install and it looks great. I’ve wanted something like this for years and finally looked it up on Amazon. I’m using this mount with my 2 year old Beltronics Pro 300 detector and the mount holds it perfectly. I like to speed, a lot! So, this mount puts the detector in the perfect spot for receiving signals from the boys in blue radar guns.

Great radar detector mount

Very well built radar detector mount. As you can see I have mine mounted and a dash cam next to it and it holds perfecy. The only thing - installing the bracket is a bit annoying if you have large hands. Very hard to tighten down those bolts and it can get very frustrating! But end of day perfect mount.

Considering the Blendmount, try this first.

So I almost convinced myself I needed the $100 Blendmount...glad I came to my senses. This thing works great and actually my be better suited for my setup (2016 Dodge Charger) than that other one. Try this one first before buying that overpriced version.

Just what every radar detector owner needs!

This is a great little device. I finally no longer need suction cups to hold up my radar detector. I was so tired of it falling down in extreme hot or cold weather. That problem is now a thing of the past. And, the price was great compared to the other mounts I saw on the market.

Radar Detector mount

This is a really nice mount. No more worrying about suction cups and having my detector falling. The only down side is that the detector is a lot closer to you. But after a while you get use to it being there.

Not bad

It works well with my beltronics RX65 but I have to flip the latch to get the device to stop sliding I just don't like the length of the screw way too long

Full Reviews